Fastener Engineering

  • Home
  • Fasteners
    • Nuts, bolts, rivets
    • Screws
    • Spacers + standoffs
    • Pins
    • Uclips + U-nuts
    • Eyebolts, rod ends, etc.
    • Thread repair kits + lockers
  • Adhesives
  • Springs
    • Compression
    • Constant force
    • Spring clip
    • Torsion springs
  • Washers / Spacers
    • Gaskets and Seals
  • Tools
  • Materials
  • Resources
    • Digital Issues
    • Leadership in Engineering
    • Suppliers
    • Video
  • Women in Engineering

Hot Melt Glue Gun for Foundries

By Design World Staff | November 12, 2008



CHARLOTTE, N.C. ‚– Power Adhesives introduces the TEC‚â„¢ 6100 hot melt glue gun for applying hot melt adhesives to sand cores in sand or die casting foundries or steel dies for faster, more efficient bonding than other bonding systems such as water-based glues.

power adhesive tec 6100.jpg


Benefits over other fixing systems include instant bonding with no wait time, improved bond application and accuracy, increased productivity and a reduction of scrap.


The TEC‚â„¢ 6100 hot melt glue gun from Power Adhesives has highly efficient twin 250 Watt steel heaters along with 500 Watts of power to meet the most demanding foundry application. Features include a fully enclosed heater housing with silicon rubber nozzle shroud for operator safety and a power-on warning indicator light for easy monitoring. A fast, even and controllable melt rate with two-piece easy flow nozzle assure fast and smooth molten glue flow for better control of the adhesive.


Advanced design housing of the TEC‚â„¢ 6100 offers maximum thermal efficiency for a fast warm up time of no more than five minutes from cold.


The gun is loaded with 1 ‚¾-inch adhesive cartridges and reloading the cartridge takes only seconds. An audible and visual signal minimizes down time. Melt rate is up to 9 lbs/hour, depending on the adhesive used and temperature requirements. Easy to Use


To use the TEC‚â„¢ 6100, connect the glue gun to an electrical supply. The adhesive melts inside the gun chamber and once melted can be extruded directly onto the sand or foam mold.


The TEC‚â„¢ hot melt glue guns comply with worldwide industrial and safety standards and are available along with spare parts and accessories through


www.poweradhesives.com


::Design World::

Tell Us What You Think! Cancel reply

Related Articles Read More >

Scope AR pairs real-time data connectivity with augmented reality for industrial jobs
Harwin launches connectors for ultra-compact applications
Kistler unveils new electromechanical joining module
The history of the world’s largest fastener distributor

MC2

Motion Control Classroom

Stay Connected

Resources

engineering whitepapers

Engineering White Papers brings a free library of engineering white papers, catalogs, software white papers and technology white papers on hundreds of engineering related topics.
Fastener Engineering
  • Fastener Suppliers
  • Advertise
  • About
  • Subscribe
  • Contact Us

Copyright © 2022 WTWH Media LLC. All Rights Reserved. The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of WTWH Media
Privacy Policy | Advertising | About Us

Search Fastener Engineering

  • Home
  • Fasteners
    • Nuts, bolts, rivets
    • Screws
    • Spacers + standoffs
    • Pins
    • Uclips + U-nuts
    • Eyebolts, rod ends, etc.
    • Thread repair kits + lockers
  • Adhesives
  • Springs
    • Compression
    • Constant force
    • Spring clip
    • Torsion springs
  • Washers / Spacers
    • Gaskets and Seals
  • Tools
  • Materials
  • Resources
    • Digital Issues
    • Leadership in Engineering
    • Suppliers
    • Video
  • Women in Engineering